Pool Heaters
A pool heater raises your water temperature as water circulates through the unit, bringing the temperature up to a comfortable level. Residential pools are heated one of two ways: a gas heater, which burns natural gas or propane to produce heat on demand, or an electric heat pump, which draws heat from the air and costs far less to run. Deciding whether to go with a gas heater or electric heat pump comes down to how you want to use your pool.
What does a pool heater do?
A pool heater has one job: it warms your water so you can swim comfortably when the pool would otherwise be too cold. It is plumbed in after the pump and filter. The water passes through a heat exchanger inside the heater, picks up heat, and returns to the pool or spa. Pool heaters and heat pumps help extend your swim season and let you hold a comfortable temperature in spring and fall, or heat your spa up for a relaxing evening.
What are the different types of pool heaters?
There are two main ways to heat a residential pool: a gas heater and an electric heat pump. They heat the water differently, cost different amounts to run, and accomplish different goals. Most pools we service around Houston use a gas heater, but a heat pump, or a heat pump and chiller combination, is a strong option depending on how you want to use your pool. Solar heating is another option in some markets, though it is uncommon here, so we focus on gas heaters and heat pumps.
Gas Heater
Gas heaters burn natural gas or propane to heat the water. A gas heater heats fast and works in any weather, which makes it the right choice for a spa, where you want to go from cold to hot in a short time. A gas heater can bring a spa up to temperature in about thirty to forty five minutes, depending on the size of the heater and the spa. The tradeoff is operating cost: gas heats quickly, but it is expensive to hold a temperature for long stretches. Gas heaters are the most common type we install around Houston.
Heat Pump & Chiller
Heat pumps pull warmth from the air and move it into the water using electricity, rather than burning fuel. A heat pump heats slowly but costs much less to run, so it is a good fit for holding a comfortable temperature across a longer swim season in spring and fall. A heat pump and chiller combination can also bring the temperature down in the heat of summer, so the water stays comfortable year round. Heat pumps lose efficiency as it gets cold, so we do not recommend one for a spa. They are becoming more popular here, and when we install them we typically use AquaCal or Raypak.
If you are unsure whether you should install a gas heater or a heat pump, give us a call at 832-473-5715 and we can talk through your needs with you.
What are the signs your pool heater needs attention?
A pool heater often gives little warning before it stops working, so it is worth knowing the signs that do show up. Some are easy to spot, others are subtle, and a few point to a safety issue rather than a simple repair. For anything involving gas, combustion, or wiring, we recommend having a Technician handle it. Here are the most common signs your heater needs attention, and what each one tends to point to.
The pool will not reach the temperature you set
If the heater runs but the water never gets to the temperature you set, there are a few things that may be happening. A common culprit is the internal bypass assembly, a part inside the manifold that may be failing. A heater that used to heat up consistently and no longer does is usually telling you something has changed inside it. A diagnostic finds out what is going on.
The heater will not fire or ignite
A heater that will not start can come down to gas supply, ignition, a safety sensor doing its job, or low water flow keeping it from firing. Modern heaters will not ignite when a safety condition is not met, which is by design. Because this involves gas and the safety circuit, it is not something to force or bypass.
The heater turns on and off without staying on
When a heater fires and then shuts off again and again without staying on, it is usually a safety sensor shutting the unit down: a high limit, a pressure or flow switch, or a temperature sensor. This is the heater protecting itself, and the cause needs to be found rather than reset and ignored.
Weak or low water flow
A heater needs a minimum amount of water moving through it to fire and run safely, and low flow is one of the most common reasons a heater will not work. The cause is often upstream: a dirty filter, a pump that is not moving enough water, or a closed or partly closed valve. Getting the flow right often clears up the heater complaint.
An error code on the display
Most modern heaters show a code when they shut down, pointing to ignition, flow, a high limit, or a sensor. The code narrows down the cause, but it tells you the unit stopped, not why the issue occurred in the first place. We read the code and trace it back to what caused it.
Leaking or water around the base
Water around the base of the heater can come from the inlet or outlet manifold, the heat exchanger, or a failed internal connection. The most common heat exchanger failure we see is corrosion, where low pH eats away at the copper from the inside until it begins to leak. Scale, overheating, or a hard freeze can cause the heat exchanger to crack. Either way, a failed heat exchanger usually means significant repair or replacement, and a leak inside a heater should be looked at before it does more damage.
One sign to act on right away: if you ever see soot, scorch marks, or smell something burning around the heater, turn it off and call us. That points to a combustion or venting problem, which is a safety issue.
These are the most common signs, but they are not the only ones. Anything involving gas, venting, or wiring should be left to a professional Technician. If your heater is not working right, even if what you are seeing is not on this list, a Pool Equipment Diagnostic is the place to start. We come out, find the cause, and explain what we found, and no work happens without your approval.
Rodents love a warm, dry heater.
A pool heater is warm, dry, and sheltered, which makes it a favorite nesting spot for rats, mice, and squirrels, especially in the cooler months when the heater is sitting unused. Once they move in, they chew through wiring and pack nests around the burner, and that is one of the most common causes of heater failure we see.
The telltale sign is nesting material, leaves, sticks, or insulation, poking out of the heater cabinet or its vents. If you see that, do not pull the panel and start clearing it out yourself. There is gas and wiring inside, and a nest can hide chewed wires and other damage. Give us a call at 832-473-5715 and we will clear it out and check everything the rodents may have gotten to.
Why does a pool heater need professional care?
A pool heater is the most complex piece of equipment on most pools. A gas heater burns natural gas or propane inside a combustion chamber, vents the exhaust, and relies on a chain of safety sensors to do that correctly. A heat pump runs on electricity and refrigerant. Both reward a little care and punish neglect.
Most of what keeps a heater healthy is simple. Keep the area around it clear, with room to breathe and nothing leaning against it or covering it, since a gas heater needs proper ventilation to burn and vent safely. Keep leaves and debris out of it. Running the heater for about thirty minutes once a month, even out of season, keeps it exercised and brings small problems to the surface before they leave you without heat when you want it.
The other half is water chemistry. Unbalanced water, low pH especially, corrodes the copper heat exchanger from the inside, and that is one of the most common reasons a heater fails early. Keeping your water balanced protects the heat exchanger, which is one more reason chemistry matters beyond the look of your pool.
Beyond that, a gas heater should be looked at by a professional. Checking combustion, venting, the gas train, the heat exchanger, and the safety circuit is not do it yourself territory: the stakes are safety, gas, and fire, not just a cold pool. When something is wrong, the safe path is to have it professionally diagnosed.
Heaters we install and service.
We are authorized providers for the brands below, and these are the heaters we install and service most often. If you are trying to figure out what heater you have, this can help you put a name to it. This is not a complete list, so if you do not see yours or want to confirm a specific model, give us a call at 832-473-5715.
Gas Heaters
Heat Pumps & Chillers
Not sure which heater is right for your pool? We will talk through the options with you and make a recommendation based on how you want to use your pool.
Frequently Asked
Questions about pool heaters.
It depends on how you want to use your pool. A gas heater heats fast and works in any weather, which makes it the right choice for a spa or for anyone who wants heat on demand. A heat pump heats slowly but costs much less to run, so it is the better choice for holding a comfortable temperature across a longer swim season in spring and fall. A heat pump and chiller combination can also bring the temperature down in the heat of summer. If you mainly want to extend your season, a heat pump is usually the better value. If you want a hot spa in under an hour, a gas heater is the answer.
We typically see pool heaters last eight to twelve years. If your pool is near the coast, salt air is harder on the equipment and you may get less. With balanced water, room around the unit, and basic upkeep, some last longer. Environment, weather exposure, rodents, and maintenance all play a part. When the heat exchanger fails or corrosion gets severe, replacing the heater is usually the better call than repairing it.
A spa heats quickly. A gas heater can bring a spa up to temperature in about thirty to forty five minutes, depending on the size of the heater and the spa. A full pool takes much longer, often several hours to days, and depends on the heater size, the pool size, and the weather. A heat pump heats more slowly than gas, which is why it suits holding a temperature rather than a fast heat up.
A heater that will not fire usually comes down to water flow, gas supply, ignition, or a safety sensor doing its job. Modern heaters are built not to fire when a safety condition is not met, so a unit that shuts itself down is often protecting itself. Because this involves gas and the safety circuit, it is not something to force or bypass. Give us a call and we will run a diagnostic to find the cause.
Yes. Keep the area around it clear so it can breathe, keep leaves and rodents out, and keep your water balanced, since low pH corrodes the heat exchanger and is a common cause of early failure. Running the heater for about thirty minutes once a month keeps it exercised and brings small problems to the surface early. A gas heater should also be looked at by a professional, since combustion, venting, and the gas train are not do it yourself territory.
We repair heaters whenever a repair makes sense. Every heater job starts with a Pool Equipment Diagnostic: we find the cause, give you an honest recommendation and an estimate, and no work happens without your approval. When a heater is old, the heat exchanger has failed, or the cost of the repair gets close to the cost of a new unit, we will tell you, and the decision is yours.
Is something wrong with your heater?
If your heater will not fire, will not maintain a temperature, or you are seeing error codes or a leak, give us a call at 832-473-5715, or contact us online. We will schedule a Pool Equipment Diagnostic and figure out what is going on.
Request Equipment Service