Salt Systems
A salt pool is still a chlorine pool. Instead of adding chlorine by hand, a salt system makes its own chlorine from the salt dissolved in your water. For most homeowners that means steadier chlorine and a lot less time spent battling issues, including algae.
What does a salt system do?
A salt system, also called a salt chlorine generator, sanitizes your pool by making chlorine out of salt. You add salt to the water, and as the water circulates through the salt cell, the system converts that salt into chlorine through a process called electrolysis. This is the same chlorine you would have in any chlorine pool, whether you use tablets, liquid, or a salt system. Once the chlorine sanitizes your water, most of it reverts back to salt and this cycle repeats. Because the system produces chlorine at a steadier rate when the pump is running, a salt pool tends to hold a more consistent chlorine level, which makes day to day maintenance easier. Many people also find a salt pool gentler on the skin and eyes.
How does a salt system work?
A salt system has two main parts that work together: the salt cell and the control unit. Salt dissolved in the pool water passes through the cell, where a low voltage charge converts it into chlorine through the process of electrolysis. The control unit powers the cell and lets you adjust how much chlorine the system makes. Here is what each part does.
The Salt Cell
The salt cell is plumbed inline after the pool filter, so all of the water passes through it. Inside are metal plates with a special coating, and when the control unit sends a charge through them, the salt in the water is converted into chlorine. The cell is the part where the chlorine is actually produced, and it is also the part that wears out over time. A salt cell is a wear item that eventually needs to be replaced, usually after about three to five years.
The Control Unit
The control unit, sometimes called the power center, is the brain of the system. It supplies power to the cell, lets you turn the chlorine output up or down, and reads the salt level in the water. Most systems also show status messages here, like a reminder to inspect the cell after so many hours of use, or a warning that the salt level has dropped too low. When a salt system has a problem, the control unit is often where you first see it.
One thing that new salt pool owners need to know is that you still have to add salt from time to time. The salt is mostly recycled, since the chlorine reverts back to salt after it sanitizes the water, but it is slowly used up over time, and you also lose some to splash out, backwashing, and rain. Most systems run best with a salt level around 3,000 to 3,500 parts per million, depending on the system, so the salt gets topped up occasionally rather than added constantly the way you would add chlorine tablets. If you are interested in exploring a salt pool, or need help with your current salt system, give us a call at 832-473-5715.
What are the signs your salt system needs attention?
A salt system usually tells you when something is off, either through the water or through a message on the control unit. Here are the most common signs to watch for, and what each one usually points to.
Your chlorine is low even though the salt level is right
If the pool keeps running low on chlorine but the salt level tests fine, the cell itself is often the reason. As the plates wear out or scale builds up on them, the cell makes less chlorine than it used to, even with plenty of salt in the water. A cell that can no longer keep up is usually near the end of its life or due for a cleaning.
A check cell, check salt, or inspect message on the control unit
Salt systems show status messages when something needs attention, like a reminder to inspect the cell after so many hours of use, or a warning that the salt level has dropped. Some of these are routine maintenance reminders and others point to a real problem. We can read what the system is reporting and tell you which one it is.
Visible calcium scale on the cell plates
If you look inside the cell and see white buildup on the plates, that is calcium scale, a byproduct of the way the cell makes chlorine. A light amount is normal, but heavier buildup coats the plates and cuts chlorine output. Scale needs to be cleaned off carefully, and how quickly it comes back tells us something about your water.
No lights or no power on the control unit
If the control unit is dark and shows no lights at all, the system is not getting power or has lost it. That can be a tripped breaker, a blown fuse inside the unit, or a failed control unit. Until it has power again the system cannot make chlorine, so this one is worth looking at promptly.
Low or no water flow keeping the cell from running
A salt cell needs a minimum amount of water flow before it will turn on, which is a built in safety feature. Low flow usually indicates an issue upstream of the cell: a dirty filter, a pump that is not moving enough water, or a closed or partly closed valve.
The salt reading does not match a separate salt level test
If the system reports a salt level that does not match a separate salt test, it can indicate that there is an issue with the salt cell or system. Sometimes the salt is genuinely low and needs topping up. Other times the salt sensor inside the cell is dirty or aging and needs cleaning or calibrating. A separate test is how we make sure that your salt cell is reading accurately.
Those are the most common signs, but not the only ones. A salt system combines water chemistry, electronics, and a cell that wears out, so the symptom does not always point straight to the cause. When something is off, a Pool Equipment Diagnostic is the place to start. We come out, find the cause, tell you what we found, and never begin work without your approval.
Why salt cells need regular cleaning and inspection.
Over time, a salt cell builds up calcium scale on its plates. It is a normal byproduct of the way it produces chlorine. The process of creating the chlorine increases the pH of the water at the plates, which pulls calcium out of the water and hardens it into white buildup. Left alone, scale coats the plates and blocks them from making chlorine, so the cell works harder, wears out faster, and can let your chlorine level drop, which is where algae often starts to grow.
Regular cleaning and inspection is what keeps a cell producing chlorine at full strength and lasting as long as it should. When we inspect a cell, we check the plates for scale, wear, or debris that may have gotten into the cell. Cleaning takes a careful hand, since the plates carry a thin coating that can be damaged, so the right cleaning solution and method matter. Name brand cells reverse their polarity to help clean themselves, which slows scale buildup between cleanings, but it does not replace a hands-on inspection.
Salt cell cleaning is a service that we offer and can help you with. If you think your chlorine level isn't holding like it should, or it's been a while since the cell was last cleaned, give us a call and we can take a look.
Salt systems we install and service.
We are an authorized dealer for all three brands below: Hayward, Pentair, and Jandy. These are the main salt systems we install and service. If you do not see your model, call us at 832-473-5715 and we can help you identify your system.
Frequently Asked
Questions about salt systems.
No. A salt pool is still a chlorine pool; it just makes its own chlorine instead of you adding it. The salt system converts the salt dissolved in the water into chlorine, which sanitizes the pool the same way as any other chlorine pool. What people notice is that the water feels softer and their pool has fewer problems, because the chlorine is produced steadily each day rather than having swings throughout the week.
Most salt cells last about three to five years before they need to be replaced. Water balance, how many hours the system runs, and how well the cell is kept clean all affect where in that range yours lands. The cell is a wear part, so replacement is normal and expected over the years.
Yes, you need to monitor your salt levels and add as needed. Salt is slowly used up over time, and you also lose some to splash out, backwashing, and rain. Most systems run best with a salt level around 3,000 to 3,500 parts per million depending on the system, so you top it up occasionally rather than adding it constantly like chlorine tablets or liquid chlorine. Be sure to refer to the manufacturer specifications for what salt level you need to maintain.
Making chlorine from salt raises pH as a byproduct, so salt pools tend to need acid added more often to keep the pH in range. It is normal and part of how the system works. Keeping pH in check matters because high pH makes the chlorine less effective and speeds up scale on the salt cell. We recommend using borates to help manage the pH in your salt pool.
Yes, there are several repairs that can be done to a salt system. Every job we do starts with a Pool Equipment Diagnostic: we find out whether the issue is the cell, the control unit, the salt level, or the water chemistry, then let you know what the findings are and provide you with an estimate.
Is something wrong with your salt system?
If your salt system is not making chlorine, is showing a check cell or check salt message, or you are seeing scale built up on the cell, give us a call at 832-473-5715, or contact us online. We will schedule a Pool Equipment Diagnostic and figure out what is going on.
Request Equipment Service